[www.youtube.com] (Go to 3.50 to 4.40 Minute)
![]()
A "shortened" version of the quarry before "EXTRACTION"
![]()
Distinctive patterns left in the quarry walls and floor.
![]()
![]()
I have added this Pic (below) with alluvial material (black arrows) at the Mesa's base as not all quarries have this feature.
The material needs very little crushing/pounding.
USAGE:
Just add the equivalent of Calcined / Limestone,Gypsum and water for workable concrete that looks virtually the same as the original Mesa.
![]()
Firstly we have to know the properties of the Calcined / Limestone and Gypsum and how it was made also what happens when water is added.
Calcined / Limestone; = SHRINKS (gap'y joints) (Longer setting time than Gypsum).
Cement clinker is made by heating, in a cement kiln, a mixture of raw materials to a calcining temperature of above 600 °C (1,112 °F) and then a fusion temperature, which is about 1,450 °C (2,640 °F) for modern cements, to sinter the materials into clinker. The materials in cement clinker are alite, belite, tri-calcium aluminate, and tetra-calcium alumino ferrite. The aluminium, iron, and magnesium oxides are present as a flux allowing the calcium silicates to form at a lower temperature,[15] and contribute little to the strength. For special cements, such as low heat (LH) and sulfate resistant (SR) types, it is necessary to limit the amount of tricalcium aluminate (3 CaO·Al2O3) formed. The major raw material for the clinker-making is usually limestone (CaCO3) mixed with a second material containing clay as source of alumino-silicate. Normally, an impure limestone which contains clay or SiO2 is used. The CaCO3 content of these limestones can be as low as 80%. Secondary raw materials (materials in the raw mix other than limestone) depend on the purity of the limestone. Some of the materials used are clay, shale, sand, iron ore, bauxite, fly ash, and slag. When a cement kiln is fired by coal, the ash of the coal acts as a secondary raw material.
Calcined / Gypsum (Plaster of Paris) = EXPANDS (Short setting time).
(Gypsum plaster
Gypsum plaster, or plaster of Paris, is produced by heating Gypsum to about 300 °F (150 °C):[15]
CaSO4·2H2O + heat → CaSO4·0.5H2O + 1.5H2O (released as steam).
You need to understand why I am giving out all this info.
Purchase some finely ground Gypsum, Calcine it (heat) till it stops bubbling.
OBSERVE: = "Liquid powder"
Later on I will explain why 26° for the A.S/D.S Passages.
The next step is to recognise heat by colour.
Can fire burn fire?
The dangerous thing about the chemical reactions in fire is the fact that they are self-perpetuating. The heat of the flame itself keeps the fuel at the ignition temperature, so it continues to burn as long as there is fuel and oxygen around it. The flame heats any surrounding fuel so it releases gases as well. (wiki)
THIS IS THE SNOWBALL EFFECT CREATED IN THE NEXT VIDEO.
[www.youtube.com]
Have you noticed the clean burn (No smoke exhausting)?
Note the red/blue/purple colour just inside the opening. = (EXTREME HEAT)!
THIS TYPE OF BURN IS THE SECRET.
This next photo shows huge amounts of (fuel + heat) being lost to the Atmosphere.
![]()
I've shown how fire can be trapped inside a confined area.
The amount of fuel and time saved if one was using "Wood" is in the ratio of;
2 Builder's wheelbarrows burnt over a period of 5 Hrs. (NO ASSIST)
IS;TO
4 Kilograms burnt in 45 Minutes.(AIR ASSIST)
How is this possible?
PREHEATING TO A POINT OF INSTANTANEOUS COMBUSTION.
To be continued.
A "shortened" version of the quarry before "EXTRACTION"
Distinctive patterns left in the quarry walls and floor.
I have added this Pic (below) with alluvial material (black arrows) at the Mesa's base as not all quarries have this feature.
The material needs very little crushing/pounding.
USAGE:
Just add the equivalent of Calcined / Limestone,Gypsum and water for workable concrete that looks virtually the same as the original Mesa.
Firstly we have to know the properties of the Calcined / Limestone and Gypsum and how it was made also what happens when water is added.
Calcined / Limestone; = SHRINKS (gap'y joints) (Longer setting time than Gypsum).
Cement clinker is made by heating, in a cement kiln, a mixture of raw materials to a calcining temperature of above 600 °C (1,112 °F) and then a fusion temperature, which is about 1,450 °C (2,640 °F) for modern cements, to sinter the materials into clinker. The materials in cement clinker are alite, belite, tri-calcium aluminate, and tetra-calcium alumino ferrite. The aluminium, iron, and magnesium oxides are present as a flux allowing the calcium silicates to form at a lower temperature,[15] and contribute little to the strength. For special cements, such as low heat (LH) and sulfate resistant (SR) types, it is necessary to limit the amount of tricalcium aluminate (3 CaO·Al2O3) formed. The major raw material for the clinker-making is usually limestone (CaCO3) mixed with a second material containing clay as source of alumino-silicate. Normally, an impure limestone which contains clay or SiO2 is used. The CaCO3 content of these limestones can be as low as 80%. Secondary raw materials (materials in the raw mix other than limestone) depend on the purity of the limestone. Some of the materials used are clay, shale, sand, iron ore, bauxite, fly ash, and slag. When a cement kiln is fired by coal, the ash of the coal acts as a secondary raw material.
Calcined / Gypsum (Plaster of Paris) = EXPANDS (Short setting time).
(Gypsum plaster
Gypsum plaster, or plaster of Paris, is produced by heating Gypsum to about 300 °F (150 °C):[15]
CaSO4·2H2O + heat → CaSO4·0.5H2O + 1.5H2O (released as steam).
You need to understand why I am giving out all this info.
Purchase some finely ground Gypsum, Calcine it (heat) till it stops bubbling.
OBSERVE: = "Liquid powder"
Later on I will explain why 26° for the A.S/D.S Passages.
The next step is to recognise heat by colour.
Can fire burn fire?
The dangerous thing about the chemical reactions in fire is the fact that they are self-perpetuating. The heat of the flame itself keeps the fuel at the ignition temperature, so it continues to burn as long as there is fuel and oxygen around it. The flame heats any surrounding fuel so it releases gases as well. (wiki)
THIS IS THE SNOWBALL EFFECT CREATED IN THE NEXT VIDEO.
[www.youtube.com]
Have you noticed the clean burn (No smoke exhausting)?
Note the red/blue/purple colour just inside the opening. = (EXTREME HEAT)!
THIS TYPE OF BURN IS THE SECRET.
This next photo shows huge amounts of (fuel + heat) being lost to the Atmosphere.
I've shown how fire can be trapped inside a confined area.
The amount of fuel and time saved if one was using "Wood" is in the ratio of;
2 Builder's wheelbarrows burnt over a period of 5 Hrs. (NO ASSIST)
IS;TO
4 Kilograms burnt in 45 Minutes.(AIR ASSIST)
How is this possible?
PREHEATING TO A POINT OF INSTANTANEOUS COMBUSTION.
To be continued.